Home

G3YRO 160m Receiving Loop

 

INTRODUCTION

I've been working a lot of DX on 160m for over 45 years . . . but sadly have never had room for a Beverage receiving aerial.

And of course, the ever increasing problem on 160m is the noise from local domestic equipment.

So . . . I thought I'd make a receiving loop, which I felt sure would give me a lower noise level.

I'm not sure why so many people make their Receiving Loops out of copper pipe or
co-ax, and just a single turn. Fine, you may need to do that if you want to make a "Magnetic Loop" transmitting aerial . . . but I figured for receive I'd be better off with a resonant multi-turn loop, made from wire, as this would generate much stronger signals. (what we usually call a "Frame Aerial")

 

DESIGN AND CONSTRUCTION

This Loop was to be installed up in my Loft, so there was no need to make anything weather-proof.

So . . . picture an upright wooden cross (made of 2" x 1"), with a horizontal boom. The length of each is 6 feet (well the upright is longer, to give it a mounting post)

I have a 4 turn loop of PVC covered multi-strand wire going round the frame (through holes drilled through the boom). Each turn is an inch apart on the booms (so slightly closer round the loop). Across the end of this winding I put a tuning capacitor to resonate it. (for testing - needed about 200 pF)

It was recommended by the designer of the Welbrook Loops that I ground the centre point of the loop to the outer of the coax feeder - he said this should reduce the noise by making it balanced about ground, rather than "floating").

Then I have a one-turn loop for the pickup, spaced the same distance (and inside the last loop winding). This is shown in red in the above diagram.

Originally this went straight to the coax back to the receiver, but I have since inserted a tiny 4:1 transformer, (8t to 2t on a 20mm ferrite core) which gives a better match.

The matching transformer and the co-ax are just held in place with plastic cable-ties around the upright timber.
 

TUNING

The tuning of the Loop is obviously quite sharp, so being remote, I resonate it using Varicap Tuning, so I can adjust it for different parts of the band by feeding DC from a Tuning Pot down the coax (via chokes and blocking capacitors).

I have two varicaps back to back across the end of the main loop winding, feeding the DC to the junction of the two, which keeps it balanced. The DC return for the diodes is already there, due to grounding the centre point of this winding.

1N5822 rectifier diodes work really well (and are easily obtained) . . . . they need about 3V to resonate on 1.8 MHz and 6V for 2.0 MHz (with no fixed padders). So from a 12V supply I have 5k pot with 3.3k to ground, and 10k to the +12V. (so you have full "bandspread" to resonate the Loop)

 

CONNECTING TO RIG

I felt it was desirable to have a Pre-Amp, so that I could properly compare signal strengths between the two antennas. I set the gain so that Local signals from the Loop are the same strength as from my main Antenna (about 12dB gain).

I already had an MFJ1026 Noise Phasing Unit (which is fine for single noise sources, but no good for multiples (fortunately I only paid a small amount for it s/h)

But I use this for the Loop . . . feeding it in the Aux Antenna input. So all the connectors and switching is already there, plus there's a variable gain pre-amp which is perfect for the Loop, and I have it set to give the same signal levels as my Tx aerial.

All I have done is re-locate the Tx Delay front panel pot to the rear panel, and used that position to mount my Varicap Tuning control on the front. Obviously it was easy to put the isolating caps, RFC etc inside, and pick up the DC all within that box, so it's very neat !

By turning the MFJ box on or off, it switches instantly between the main Tx Antenna or the Loop. (you can even phase the two, if desired)

If you don't already have a similar unit, and you're using a Transceiver, you would need to make a simple relay switching box to switch over to the Loop on Receive - de-activating the Relay would mean Receiving on your Tx Antenna. This box would obviously include the Varicap Tuning control, and a Pre-amp.


USE IN PRACTICE

When you rotate the Loop, I found that the nulls on signals are very sharp (off the sides), but the directivity (off the ends) is quite broad. What I immediately noticed is that I found a big Null on my general background noise in one position.

Fortunately, that position is with the Loop pointing East-West, which is a pretty good direction for working most DX from Europe. So the Loop is installed up in my Loft, pointing East-West. With the vertical timber about 7ft long, it just fits between the apex of the roof and the floor.

My main antenna for 160m is a horizontal Dipole. So it's very interesting having a different Receive antenna that is Vertically polarised.

Most DX signals are stronger on the Loop, some are better on the Dipole, depending on Propagation. European stations are usually stronger on the Dipole, but sometimes stronger on the Loop, again depending on Propagation. (this is why I find it so interesting having a different Rx antenna, for the first time)

Local Ground-wave signals off the side of the Loop almost disappear . . . but once you have Sky-wave signals, although ones off the side are attenuated, it's not so drastic, so you may still have a better signal-to-noise ratio.

If you build one of these Loops, do let me know how you get on!  Or email if you have any questions.

g3yro@hotmail.com
 

Home